How To Remove Agitator From Ge Washer Gtw335asn1ww?

How to Remove the Agitator from a GE Washer GTW335ASN1WW

Your GE washer’s agitator is a cylindrical drum that helps to clean your clothes by agitating them in the water. Over time, the agitator can become clogged with dirt and debris, which can reduce its effectiveness and lead to poor washing results. If your agitator is clogged, you may need to remove it and clean it.

This guide will show you how to remove the agitator from a GE washer GTW335ASN1WW. It’s a simple process, but it’s important to follow the steps carefully to avoid damaging your washer.

What you’ll need:

• A Phillips head screwdriver
• A flathead screwdriver
• A pair of pliers
• A bucket
• A hose
• Warm water
• Dish soap

Step 1: Turn off the washer and unplug it from the wall.

Step 2: Open the lid of the washer and locate the agitator. The agitator is a cylindrical drum that is located in the center of the washing machine. It is connected to the motor by a drive belt.

Step 3: Remove the agitator cap. The agitator cap is a small, round cap that is located on top of the agitator. It is held in place by a Phillips head screw. Use a Phillips head screwdriver to remove the screw and remove the cap.

Step 4: Disconnect the drive belt. The drive belt is a black rubber belt that connects the agitator to the motor. It is located under the agitator cap. Use a flathead screwdriver to pry up the tab on the drive belt and disconnect it from the motor.

Step 5: Remove the agitator. The agitator is now free to be removed. Use a pair of pliers to grip the agitator and pull it out of the washing machine.

Step 6: Clean the agitator. The agitator is now removed and can be cleaned. Fill a bucket with warm water and dish soap. Dip the agitator in the water and scrub it with a brush to remove any dirt or debris.

Step 7: Reattach the agitator. Rinse the agitator off with warm water and dry it with a towel. Reattach the agitator to the washing machine by inserting it into the hole in the center of the washing machine. Reconnect the drive belt by snapping it into place. Replace the agitator cap and tighten the screw.

Step 8: Turn on the washer and test it. Plug the washer back into the wall and turn it on. Run a cycle with warm water and no detergent to clean out any remaining dirt or debris.

Step	Instructions	Image
1	Turn off the washer and unplug it from the outlet.
2	Open the lid of the washer.
3	Locate the agitator. It is the large, cylindrical part in the center of the tub.
4	Press down on the release button on the top of the agitator and turn it counterclockwise to remove it.
5	Clean the agitator with a mild detergent and water.
6	Reinsert the agitator into the tub and turn it clockwise until it is locked in place.

Tools and Materials Needed

To remove the agitator from a GE washer GTW335ASN1WW, you will need the following tools and materials:

• Phillips head screwdriver
• Adjustable wrench
• Penetrating oil
• Rags

Steps to Remove the Agitator

1. Turn off the power to the washing machine and disconnect the power cord.
2. Locate the agitator. The agitator is the cylindrical part in the center of the washing machine drum.
3. Remove the agitator cap. The agitator cap is a small, round cap located on top of the agitator. It is held in place by a Phillips head screw. Use the Phillips head screwdriver to remove the screw and remove the agitator cap.
4. Apply penetrating oil to the agitator shaft. The agitator shaft is the metal rod that the agitator is attached to. Apply penetrating oil to the agitator shaft to help loosen it.
5. Use an adjustable wrench to loosen the agitator nut. The agitator nut is a large, round nut located at the bottom of the agitator shaft. Use the adjustable wrench to loosen the agitator nut.
6. Remove the agitator. Once the agitator nut is loose, you can remove the agitator by pulling it straight up.

Troubleshooting

If you are having trouble removing the agitator, there are a few things you can check:

• Make sure that you have turned off the power to the washing machine and disconnected the power cord.
• Make sure that you have located the agitator.
• Make sure that you have removed the agitator cap.
• Make sure that you have applied penetrating oil to the agitator shaft.
• Make sure that you are using the correct size adjustable wrench to loosen the agitator nut.

If you are still having trouble removing the agitator, you may need to contact a qualified appliance repair technician.

Removing the agitator from a GE washer GTW335ASN1WW is a relatively simple task that can be completed by most DIYers. By following the steps in this guide, you can safely and easily remove the agitator from your washing machine.

How to Remove Agitator from GE Washer GTW335ASN1WW?

This guide will show you how to remove the agitator from a GE washing machine model GTW335ASN1WW. The agitator is the central part of the washing machine that rotates to agitate the clothes during the wash cycle. It is important to remove the agitator before cleaning the washing machine or replacing the drain pump.

Tools and Materials

• Adjustable wrench
• Flathead screwdriver
• Phillips head screwdriver
• Penetrating oil
• Rag

Steps

1. Unplug the washing machine from the wall outlet.
2. Turn off the water supply to the washing machine.
3. Remove the detergent dispenser.
4. Turn the washing machine on and allow it to fill with water.
5. Use the flathead screwdriver to pry up the tabs on the agitator cap.
6. Remove the agitator cap.
7. Use the adjustable wrench to loosen the nut that holds the agitator in place.
8. Remove the agitator.
9. Wipe down the inside of the washing machine with a rag.
10. Reassemble the washing machine.

Tips

• If the agitator is stuck, you can try applying penetrating oil to the nut and letting it sit for a few minutes before trying to loosen it.
• Be careful not to drop the agitator when removing it.
• Make sure to replace the agitator cap before using the washing machine again.

By following these steps, you can safely remove the agitator from your GE washing machine model GTW335ASN1WW. This will allow you to clean the washing machine or replace the drain pump more easily.

How do I remove the agitator from my GE washer GTW335ASN1WW?

1. Turn off the washer and unplug it from the wall.
2. Open the lid of the washer and locate the agitator. The agitator is the large, cylindrical piece in the center of the tub.
3. Remove the cap from the top of the agitator. The cap is a small, round piece of plastic that is located in the center of the agitator.
4. Insert a flat-head screwdriver into the hole in the center of the agitator. Turn the screwdriver clockwise to loosen the agitator.
5. Pull the agitator up and out of the tub. The agitator should come out easily.

What if the agitator is stuck?

If the agitator is stuck, you can try the following:

1. Use a penetrating oil to loosen the agitator. Spray the oil around the agitator and let it sit for a few minutes.
2. Use a hammer to tap around the agitator. This may help to loosen it.
3. Use a wrench to turn the agitator. Be careful not to damage the agitator.

What do I do with the agitator after I remove it?

You can dispose of the agitator in the trash or recycle it.

How often should I clean the agitator?

You should clean the agitator every few months to prevent build-up of dirt and grime.

How do I clean the agitator?

To clean the agitator, you can use the following steps:

1. Turn off the washer and unplug it from the wall.
2. Open the lid of the washer and locate the agitator.
3. Remove the cap from the top of the agitator.
4. Pour a cup of white vinegar into the hole in the center of the agitator.
5. Turn the washer on and let it run for a cycle.
6. After the cycle is complete, remove the agitator and rinse it with warm water.
7. Dry the agitator with a towel and replace the cap.

What are the signs that the agitator needs to be replaced?

The agitator may need to be replaced if it is:

• Damaged
• Worn out
• Not spinning properly
• Causing the washer to make a loud noise

How do I replace the agitator in my GE washer GTW335ASN1WW?

To replace the agitator in your GE washer GTW335ASN1WW, you can follow these steps:

1. Turn off the washer and unplug it from the wall.
2. Open the lid of the washer and locate the agitator.
3. Remove the cap from the top of the agitator.
4. Unscrew the two screws that hold the agitator in place.
5. Pull the agitator up and out of the tub.
6. Insert the new agitator into the tub and secure it with the two screws.
7. Replace the cap on the top of the agitator.
8. Turn the washer on and test the agitator to make sure it is working properly.

In this blog post, we have discussed how to remove the agitator from a GE washer model GTW335ASN1WW. We have provided step-by-step instructions, along with pictures, to make the process as easy as possible. We hope that this information has been helpful to you.

Here are the key takeaways from this blog post:

• The agitator is located in the center of the washing machine drum.
• To remove the agitator, you will need to disconnect the power cord from the washer and turn off the water supply.
• You will also need to remove the detergent dispenser and the drain hose.
• Once the agitator is loose, you can lift it out of the washing machine drum.
• Be sure to reinstall the agitator in the correct orientation when you are finished.

We hope that this information has been helpful to you. If you have any questions, please do not hesitate to contact us.