How To Hardwire Redtiger Dash Cam?

How to Hardwire a Redtiger Dash Cam

Your Redtiger dash cam is a powerful tool for recording your driving and protecting yourself in the event of an accident. But did you know that you can also hardwire it to your car’s electrical system? This will give you a number of benefits, including:

• Constant power: A hardwired dash cam will always be on, even when your car is turned off. This means that you’ll never miss a moment of footage, even if you’re in an accident and your car’s battery dies.
• No battery drain: A hardwired dash cam won’t drain your car’s battery, even if you leave it on for long periods of time. This is because it will only draw power when it’s recording.
• Simplicity: Hardwiring a dash cam is a simple process that can be completed in just a few minutes. You don’t need any special tools or skills, and you won’t have to worry about running wires all over your car.

In this article, we’ll show you how to hardwire a Redtiger dash cam to your car’s electrical system. We’ll provide step-by-step instructions and tips, so you can be sure that the job is done correctly.

So if you’re ready to take your dash cam to the next level, read on!

Step	Instructions	Image
1	Locate the fuse box in your vehicle.
2	Find a fuse that is not in use.
3	Remove the fuse from the fuse box.
4	Connect the red wire from the dash cam to the fuse.
5	Connect the black wire from the dash cam to a ground point in the vehicle.
6	Turn on the ignition and verify that the dash cam is powered on.

A dash cam is a valuable tool for recording your driving and protecting yourself in the event of an accident. However, most dash cams are powered by a battery, which means they only last for a few hours before they need to be recharged. If you want to have a dash cam that is always recording, you need to hardwire it to your car’s electrical system.

Hardwiring a dash cam is a relatively simple process, but it does require some basic tools and skills. In this tutorial, we will show you how to hardwire a Redtiger dash cam to your car’s electrical system.

Tools and Materials

• Redtiger dash cam
• Hardwire kit
• Phillips head screwdriver
• Wire cutters
• Crimping tool
• Electrical tape

Preparation

Before you begin, you need to gather all of the necessary tools and materials. You will also need to turn off the car and disconnect the negative battery terminal.

1.Locate the fuse box in the car.

The fuse box is usually located under the dashboard or in the glove compartment. Once you have located the fuse box, open it up and take a look at the diagram. This diagram will show you which fuses are responsible for powering different components in the car, such as the cigarette lighter.

2.Find the fuse that powers the cigarette lighter.

The fuse that powers the cigarette lighter is usually labeled “CIG” or “P/S.” Once you have located the fuse, remove it from the fuse box.

3.Connect the red wire from the hardwire kit to the fuse.

The red wire from the hardwire kit is the positive wire. It should be connected to the fuse that powers the cigarette lighter. You can use a wire crimper to connect the two wires together.

4.Connect the black wire from the hardwire kit to a ground point.

The black wire from the hardwire kit is the negative wire. It should be connected to a ground point in the car. A good place to connect the ground wire is to the metal chassis of the car.

5.Reattach the negative battery terminal.

Once you have connected the hardwire kit to the car’s electrical system, you can reattach the negative battery terminal.

6.Turn on the car and test the dash cam.

Turn on the car and turn on the dash cam. The dash cam should now be powered by the car’s electrical system and it should be recording continuously.

Hardwiring a dash cam is a relatively simple process, but it does require some basic tools and skills. By following the steps in this tutorial, you can hardwire a Redtiger dash cam to your car’s electrical system in just a few minutes.

How To Hardwire Redtiger Dash Cam?

Overview

A dash cam is a valuable tool for recording your driving experiences and providing evidence in the event of an accident. However, most dash cams are powered by a battery, which means that they will eventually run out of power. If you want your dash cam to be recording all the time, you will need to hardwire it to your car’s electrical system.

Hardwiring a dash cam is a relatively simple task, but it does require some basic electrical knowledge. In this guide, we will walk you through the process of hardwiring a Redtiger dash cam to your car.

Tools and Materials

To hardwire a Redtiger dash cam, you will need the following tools and materials:

• A Redtiger dash cam
• A hardwire kit
• A Phillips head screwdriver
• A wire cutter
• A wire stripper
• Electrical tape

Instructions

To hardwire a Redtiger dash cam, follow these steps:

1. Turn off the car and disconnect the negative battery terminal.
2. Locate the fuse box in your car. The fuse box is usually located under the dashboard or in the engine compartment.
3. Find the fuse that powers the cigarette lighter. The cigarette lighter fuse is usually labeled “CIG” or “CIGAR”.
4. Remove the fuse from the fuse box.
5. Connect the yellow wire from the hardwire kit to the fuse that powers the cigarette lighter.
6. Route the yellow wire through the car’s interior.
7. Plug the dash cam into the cigarette lighter adapter.
8. Reconnect the negative battery terminal.

Testing

Turn on the car and start the engine. Make sure that the dash cam is turned on and that the video is recording. Test the dash cam by recording a short video.

Bonus Tip

If you are not comfortable with electrical work, you can have a professional install the hardwire kit for you.

Hardwiring a Redtiger dash cam is a simple task that can be completed in a few minutes. By following these instructions, you can ensure that your dash cam is always recording, even when your car is turned off.

How to Hardwire a Redtiger Dash Cam?

• What do I need to hardwire my Redtiger dash cam?

To hardwire your Redtiger dash cam, you will need:

• A Redtiger dash cam
• A hardwire kit (sold separately)
• A 12V power source, such as a car cigarette lighter outlet
• A Phillips head screwdriver

• How do I hardwire my Redtiger dash cam?

1. Turn off your car and disconnect the negative battery terminal.
2. Locate the 12V power source in your car. This is typically located in the center console or under the dashboard.
3. Remove the cover of the power source and connect the red wire from the hardwire kit to the positive terminal of the power source.
4. Connect the black wire from the hardwire kit to the negative terminal of the power source.
5. Secure the hardwire kit to the car with the included adhesive strips.
6. Reconnect the negative battery terminal and turn on your car.

• What are the benefits of hardwiring my Redtiger dash cam?

There are several benefits to hardwiring your Redtiger dash cam, including:

• Continuous recording: When your car is turned off, your dash cam will continue to record, so you don’t miss any important footage.
• Reduced battery drain: Hardwiring your dash cam means that it will not drain your car’s battery, even when the car is turned off.
• More reliable power: A hardwire kit provides a more reliable power source than a cigarette lighter adapter, which can be prone to disconnection.

• What are the risks of hardwiring my Redtiger dash cam?

There are a few risks associated with hardwiring your Redtiger dash cam, including:

• Damage to your car: If you are not careful, you could damage your car’s electrical system by hardwiring your dash cam incorrectly.
• Fire hazard: If the hardwire kit is not installed correctly, it could create a fire hazard.

• How can I avoid the risks of hardwiring my Redtiger dash cam?

To avoid the risks of hardwiring your Redtiger dash cam, you should:

• Only use a hardwire kit that is designed for your dash cam.
• Follow the instructions carefully when installing the hardwire kit.
• Have a qualified technician install the hardwire kit if you are not comfortable doing it yourself.

• Can I hardwire my Redtiger dash cam to a battery maintainer?

Yes, you can hardwire your Redtiger dash cam to a battery maintainer. This is a good option if you want your dash cam to continue recording even when your car is not in use for long periods of time.

• Can I hardwire my Redtiger dash cam to a fuse box?

Yes, you can hardwire your Redtiger dash cam to a fuse box. This is a good option if you want your dash cam to be powered on even when your car is turned off.

• What are the different types of hardwire kits available?

There are two main types of hardwire kits available:

• Direct wire kits: These kits connect directly to your car’s electrical system.
• Cigarette lighter adapter kits: These kits connect to your car’s cigarette lighter outlet.

• Which type of hardwire kit is best for me?

The best type of hardwire kit for you will depend on your individual needs and preferences. If you are not comfortable working with your car’s electrical system, a cigarette lighter adapter kit may be a better option. However, if you want your dash cam to be powered on even when your car is turned off, a direct wire kit may be a better option.

• Can I hardwire my Redtiger dash cam myself?

Hardwiring your Redtiger dash cam is a relatively simple process, but it is important to follow the instructions carefully to avoid damaging your car’s electrical system. If you are not comfortable working with your car’s electrical system, you should have a qualified technician install the hardwire kit for you.

In this blog post, we have discussed how to hardwire a Redtiger dash cam. We have covered the steps involved in the process, as well as some of the things you need to keep in mind. By following these steps, you can easily hardwire your dash cam and enjoy all of its features.

Here are some key takeaways from this blog post:

• Hardwiring a dash cam is a relatively simple process, but it is important to follow the steps carefully.
• You will need to have a few tools and materials on hand, including a dash cam, a wiring kit, and a fuse tap.
• The most important thing to remember when hardwiring a dash cam is to make sure that the power source is properly fused.
• By following these steps, you can easily hardwire your dash cam and enjoy all of its features.