How To Prime Goulds Jet Pump?

How to Prime a Goulds Jet Pump

Goulds jet pumps are a popular choice for homeowners and businesses alike, thanks to their ability to provide reliable water pressure even in challenging conditions. However, before you can enjoy the benefits of a Goulds jet pump, you need to know how to prime it properly.

Priming a Goulds jet pump is a relatively simple process, but it’s important to do it correctly to ensure that the pump is working properly. In this article, we’ll walk you through the steps of priming a Goulds jet pump, so you can get your pump up and running in no time.

We’ll also provide some tips on how to troubleshoot common priming problems, so you can be sure that your pump is operating at its best.

Step	Instructions	Image
1	Turn off the pump and close the shut-off valve.
2	Remove the priming plug from the top of the pump.
3	Fill the pump housing with water.
4	Replace the priming plug and open the shut-off valve.
5	Turn on the pump and allow it to run for a few minutes to prime.

Preparing the Pump for Priming

Before you can prime a Goulds jet pump, you need to make sure that the pump is properly prepared. This includes:

• Turning off the power to the pump. This is important to prevent any injuries from electrical shock.
• Disconnecting the discharge hose from the pump. This will allow you to fill the pump with water without having to worry about it flowing back out.
• Opening the air bleed valve on the pump. This valve is located on the top of the pump and allows air to escape as the pump is primed.
• Filling the pump with water. You can do this by pouring water directly into the pump housing or by attaching a garden hose to the inlet port and turning on the water.

Once the pump is filled with water, you can close the air bleed valve and reconnect the discharge hose. You are now ready to prime the pump.

Priming the Pump

Priming a Goulds jet pump is a relatively simple process. To do this, follow these steps:

1. Turn on the power to the pump.
2. Place the end of the discharge hose in a bucket of water.
3. Open the discharge valve on the pump.
4. Listen for the pump to start priming.
5. Once the pump is primed, the water will flow out of the discharge hose and into the bucket.

You may need to repeat these steps a few times to ensure that the pump is properly primed. Once the pump is primed, you can turn off the power and reconnect the discharge hose to the plumbing system.

Priming a Goulds jet pump is a simple process that can be completed in a few minutes. By following these steps, you can ensure that your pump is properly primed and functioning properly.

3. Starting the Pump

Once the pump is primed, it’s time to start it. To do this, follow these steps:

1. Turn on the power to the pump. This may be a switch on the pump itself, or it may be a switch at the circuit breaker panel.
2. Open the discharge valve. This is the valve that allows water to flow out of the pump and into the sprinkler system.
3. Turn on the water supply to the pump. This may be a valve on the water main, or it may be a valve at the well.

The pump should start running and water should begin flowing out of the discharge valve. If the pump does not start running, there may be a problem with the power supply, the discharge valve, or the water supply.

4. Testing the Pump

Once the pump is running, it’s important to test it to make sure it’s working properly. To do this, follow these steps:

1. Turn on the sprinkler system. This will allow you to see if the water is flowing properly through the sprinklers.
2. Check the pressure gauge on the pump. The pressure should be between 40 and 60 psi.
3. Listen for any unusual noises coming from the pump. If you hear any strange noises, it may be a sign of a problem.

If the pump is not working properly, you may need to have it serviced or repaired.

Priming and starting a Goulds jet pump is a relatively simple process. By following these steps, you can ensure that your pump is working properly and that you’re getting the most out of your sprinkler system.

How do I prime a Goulds jet pump?

1. Turn off the power to the pump and close the shut-off valve on the discharge line.
2. Locate the priming port on the pump. This is typically a small hole located near the top of the pump.
3. Fill a bucket with water and carefully pour it into the priming port until the pump is full.
4. Open the shut-off valve and turn on the power to the pump. The pump should start to prime and the water will begin to flow out of the discharge line.
5. Allow the pump to run for a few minutes to make sure that it is primed properly. The water should flow out of the discharge line steadily and without any air bubbles.

What if the pump won’t prime?

There are a few possible reasons why the pump might not be priming.

• The pump may not be getting enough water. Make sure that the water supply is turned on and that the shut-off valve is open.
• The pump may be clogged. Check the inlet screen and the impeller for any debris that may be blocking the flow of water.
• The pump may be damaged. If the pump is old or has been damaged, it may not be able to prime properly.

If you have checked all of these things and the pump still won’t prime, you may need to call a qualified plumber to help you troubleshoot the problem.

How often do I need to prime the pump?

You should prime the pump whenever you start it up for the first time, after it has been turned off for a long period of time, or after the water level in the well has dropped.

What is the difference between a jet pump and a submersible pump?

A jet pump is a type of centrifugal pump that uses a jet of water to create suction and draw water from a well. A submersible pump is a type of centrifugal pump that is completely submerged in the water that it is pumping.

Jet pumps are typically used for shallow wells, while submersible pumps are typically used for deeper wells. Jet pumps are also more affordable than submersible pumps.

What are the advantages and disadvantages of jet pumps?

The advantages of jet pumps include:

• They are relatively affordable.
• They are easy to install.
• They can be used for shallow wells.

The disadvantages of jet pumps include:

• They are not as efficient as submersible pumps.
• They can be noisy.
• They require a priming tank.

What are the advantages and disadvantages of submersible pumps?

The advantages of submersible pumps include:

• They are very efficient.
• They are quiet.
• They do not require a priming tank.

The disadvantages of submersible pumps include:

• They are more expensive than jet pumps.
• They are more difficult to install.
• They can only be used for deep wells.

Which type of pump is right for me?

The best type of pump for you depends on your specific needs and budget. If you have a shallow well and are looking for an affordable option, a jet pump is a good choice. If you have a deep well and are looking for a more efficient option, a submersible pump is a good choice.

In this blog post, we have discussed how to prime a Goulds jet pump. We have covered the steps involved in the priming process, as well as some tips and tricks to help you get the job done quickly and easily. We hope that this information has been helpful, and that you are now able to prime your Goulds jet pump with confidence.

Here are some key takeaways from this blog post:

• Priming a Goulds jet pump is a relatively simple process, but it is important to follow the steps carefully to avoid damaging the pump.
• The most important step in the priming process is to make sure that the pump is filled with water before it is turned on.
• You can prime a Goulds jet pump by using a bucket of water, a garden hose, or a priming pump.
• If you are having trouble priming your pump, you can try using a priming aid or a vacuum breaker.
• Once the pump is primed, you should be able to hear water flowing through the impeller.
• If you do not hear water flowing through the impeller, the pump may not be primed properly. You can try priming the pump again or you may need to have the pump serviced.