How To Tighten Ninja 400 Chain?

How to Tighten a Ninja 400 Chain

Your Ninja 400’s chain is one of the most important components of your bike. It’s responsible for transmitting power from your engine to the rear wheel, so it’s essential that it’s properly maintained. One of the most important aspects of chain maintenance is keeping it properly tensioned. A loose chain can cause damage to your sprockets and other components, while a too-tight chain can make your bike difficult to ride and even lead to premature wear.

In this article, we’ll show you how to properly tighten your Ninja 400’s chain. We’ll also provide some tips on how to keep your chain in good condition and extend its lifespan.

So, if you’re ready to learn how to tighten your Ninja 400’s chain, read on!

Step	Instructions	Image
1	Put the bike on a center stand or have someone hold it upright.
2	Locate the chain tensioner on the left side of the bike.
3	Turn the tensioner clockwise to tighten the chain.
4	Check the chain slack by pulling up on the lower run of chain. There should be about 1/2 inch of slack.
5	If the chain is too tight, turn the tensioner counterclockwise to loosen it.
6	Once the chain is properly adjusted, tighten the tensioner locknut.

Tools and Materials

To tighten the chain on your Ninja 400, you will need the following tools and materials:

• Chain tool
• Chain lube
• 17mm wrench
• 12mm wrench
• Torque wrench

Procedure

1. Park your Ninja 400 on a level surface and set the parking brake.
2. Put on your safety glasses.
3. Locate the chain tensioner on the left side of the bike.
4. Use the 12mm wrench to loosen the locknut on the chain tensioner.
5. Use the 17mm wrench to turn the adjuster bolt on the chain tensioner clockwise until the chain is tight.
6. Retighten the locknut on the chain tensioner.
7. Check the chain tension by bouncing the bike up and down.
8. The chain should have about 1-inch of play when you bounce the bike.
9. If the chain is too tight, loosen the locknut and adjuster bolt and repeat steps 5-7.
10. If the chain is too loose, tighten the locknut and adjuster bolt and repeat steps 5-7.
11. Lubricate the chain with chain lube.
12. Check the chain tension again and make sure it is correct.

Tightening the chain on your Ninja 400 is a simple task that can be completed in a few minutes. By following these steps, you can ensure that your bike is properly maintained and that your chain is safe and reliable.

Here are some additional tips for maintaining your Ninja 400’s chain:

• Check the chain tension regularly and adjust it as needed.
• Clean the chain regularly with a degreaser and a brush.
• Lubricate the chain regularly with a good quality chain lube.
• Replace the chain when it is worn out.

By following these tips, you can keep your Ninja 400’s chain in good condition and ensure that it performs properly.

How To Tighten Ninja 400 Chain?

The Ninja 400 is a popular sportbike that is known for its nimble handling and powerful engine. However, one of the most important things to keep in mind when owning a Ninja 400 is maintaining the chain properly. A loose chain can cause damage to the sprockets and other components, while a tight chain can be uncomfortable to ride and even dangerous.

To ensure that your Ninja 400’s chain is properly maintained, it is important to check the tension regularly and adjust it as needed. The following steps will show you how to tighten the chain on your Ninja 400:

1. Park your Ninja 400 on a level surface and put the transmission in neutral.
2. Locate the chain tensioner on the left side of the bike.
3. Turn the tensioner clockwise to tighten the chain.
4. Check the chain tension by lifting it up at the center.
5. The chain should have about 1/2 inch of play.
6. If the chain is too loose, continue to turn the tensioner clockwise.
7. If the chain is too tight, turn the tensioner counterclockwise.
8. Repeat steps 4-7 until the chain is properly tensioned.

Once you have adjusted the chain tension, it is important to test ride your Ninja 400 to make sure that it is running smoothly. If you notice any problems, such as a rattling noise or a loss of power, you may need to adjust the chain tension again.

Troubleshooting

If you are having trouble tightening the chain on your Ninja 400, there are a few things you can check to troubleshoot the problem.

• Make sure that the chain is properly lubricated. A dry chain will be more difficult to tighten.
• Check the chain for damage. If the chain is worn or damaged, it will need to be replaced before you can tighten it.
• Check the tensioner for damage. If the tensioner is damaged, it will not be able to properly tighten the chain.
• Check the alignment of the sprockets. If the sprockets are not aligned properly, the chain will not be able to be tightened evenly.

If you have checked all of these things and you are still having trouble tightening the chain, you may need to take your Ninja 400 to a qualified mechanic for assistance.

Tips and Tricks

Here are a few tips and tricks to help you keep your Ninja 400’s chain properly maintained:

• Check the chain tension regularly. The chain should be checked for tension every 500 miles or so.
• Lubricate the chain regularly. The chain should be lubricated every 1,000 miles or so.
• Replace the chain when it is worn out. The chain should be replaced every 20,000 miles or so.
• Take your Ninja 400 to a qualified mechanic for a chain inspection every 10,000 miles or so. A qualified mechanic can inspect the chain for wear and damage and make sure that it is properly adjusted.

By following these tips and tricks, you can help keep your Ninja 400’s chain in good condition and extend its lifespan.

Tightening the chain on your Ninja 400 is a relatively simple task that can be completed in a few minutes. By following the steps in this guide, you can ensure that your chain is properly maintained and that your Ninja 400 is running smoothly.

How do I tighten the chain on my Ninja 400?

1. Park your Ninja 400 on a level surface and put the bike in neutral.
2. Use a rear stand to lift the rear wheel off the ground.
3. Locate the chain tensioner on the left side of the bike.
4. Turn the tensioner clockwise to tighten the chain.
5. Check the chain slack by pulling up on the chain at the center of the rear wheel.
6. The chain should have about 1/2 inch of slack.
7. If the chain is too tight, turn the tensioner counterclockwise to loosen it.
8. Repeat steps 5-7 until the chain has the correct amount of slack.
9. Lower the bike and ride it around the block to check for any problems.

What tools do I need to tighten the chain on my Ninja 400?

You will need the following tools to tighten the chain on your Ninja 400:

• A 17mm wrench
• A 19mm wrench
• A torque wrench

How often should I tighten the chain on my Ninja 400?

You should check and tighten the chain on your Ninja 400 every 500 miles.

What happens if the chain is too tight?

If the chain is too tight, it can cause the following problems:

• Increased wear on the chain and sprockets
• Reduced performance
• A noisy chain
• A potential loss of control of the bike

What happens if the chain is too loose?

If the chain is too loose, it can cause the following problems:

• Increased wear on the chain and sprockets
• Reduced performance
• A noisy chain
• A potential loss of control of the bike

**How do I adjust the chain slack on my Ninja 400?

To adjust the chain slack on your Ninja 400, follow these steps:

1. Park your Ninja 400 on a level surface and put the bike in neutral.
2. Use a rear stand to lift the rear wheel off the ground.
3. Locate the chain tensioner on the left side of the bike.
4. Turn the tensioner clockwise to tighten the chain.
5. Check the chain slack by pulling up on the chain at the center of the rear wheel.
6. The chain should have about 1/2 inch of slack.
7. If the chain is too tight, turn the tensioner counterclockwise to loosen it.
8. Repeat steps 5-7 until the chain has the correct amount of slack.
9. Lower the bike and ride it around the block to check for any problems.

In this blog post, we have discussed how to tighten the Ninja 400 chain. We have covered the steps in detail, with images to help you visualize the process. We have also provided some tips on how to maintain your chain so that it stays in good condition for longer.

We hope that this blog post has been helpful. If you have any other questions about how to maintain your Ninja 400, please do not hesitate to contact us.