How To Enter Walk Mode In Ats?

How to Enter Walk Mode in ATS

ATS, or Automatic Train Stop, is a safety system that prevents trains from running over signals. It is activated when a train approaches a red signal, and it applies the brakes to the train automatically. However, there may be times when you need to enter walk mode in ATS. This can be done for a variety of reasons, such as if you need to inspect the track or if you need to move the train slowly.

In this article, we will discuss how to enter walk mode in ATS. We will also provide some tips on how to use walk mode safely.

What is Walk Mode?

Walk mode is a temporary state that allows a train to move slowly without being stopped by ATS. When a train is in walk mode, the brakes are released, but the train is still controlled by the ATS system. This means that the train will not exceed a certain speed, and it will stop automatically if it approaches a red signal.

How to Enter Walk Mode

To enter walk mode, you must first press the “Walk Mode” button on the control panel. This will activate the walk mode indicator light. You will then need to use the throttle to control the speed of the train. The train will not exceed a speed of 5 mph in walk mode.

Tips for Using Walk Mode Safely

When using walk mode, it is important to be aware of the following:

• You are still responsible for the safe operation of the train. Even though the brakes are released in walk mode, the train is still controlled by the ATS system. This means that you must be careful not to exceed the speed limit or to approach a red signal.
• Walk mode is not a substitute for a flagman. If you need to inspect the track or move the train slowly, you should always use a flagman. A flagman can help to ensure that the train is safe and that there are no obstructions on the track.
• Walk mode should only be used for short distances. Walk mode is a temporary state that should only be used for short distances. If you need to move the train for a long distance, you should use the normal operating mode.

By following these tips, you can use walk mode safely and effectively.

Step	Action	Explanation
1	Press the F1 key.	This will open the **ATS Help** window.
2	Click the **Walk Mode** tab.	This will display the **Walk Mode** options.
3	Click the **Enable Walk Mode** checkbox.	This will enable **Walk Mode**.
4	Click the **Close** button.	This will close the **ATS Help** window.

ATS (Automatic Train Stop) is a safety system that prevents trains from exceeding a pre-determined speed. Walk Mode is a special mode that allows the train to be moved at a slow speed for purposes such as inspection or maintenance.

This article will provide step-by-step instructions on how to enter Walk Mode in an ATS.

Step 1: Enable Walk Mode

1. Press the Walk Mode button on the ATS control panel.
2. The ATS will enter Walk Mode and the Walk Mode indicator light will illuminate.

Step 2: Set the Speed

1. Use the Speed control to set the desired speed.
2. The speed can be set from 0 to 10 mph.

Entering Walk Mode in an ATS is a simple process that can be completed in just a few steps. By following these instructions, you can safely move your train at a slow speed for purposes such as inspection or maintenance.

Additional Information

In addition to the steps listed above, there are a few other things to keep in mind when using Walk Mode in an ATS.

• Always make sure that the ATS is in Walk Mode before moving the train.
• Never exceed the maximum speed of 10 mph while in Walk Mode.
• Be aware of your surroundings and potential hazards when operating the train in Walk Mode.

By following these tips, you can safely use Walk Mode in an ATS to perform inspections and maintenance on your train.

Troubleshooting

If you are having trouble entering Walk Mode in your ATS, there are a few things you can check.

• Make sure that the ATS is properly powered on.
• Make sure that the Walk Mode button is not damaged or malfunctioning.
• Try resetting the ATS by turning it off and then back on.

If you are still having trouble, contact your ATS manufacturer for assistance.

Step 1: Power On the ATS

To enter walk mode on an ATS, you must first power on the ATS. To do this, follow these steps:

1. Locate the power switch on the ATS. The power switch is typically located on the front panel of the ATS.
2. Turn the power switch to the “On” position.

Once the ATS is powered on, the Walk Mode indicator light will illuminate. This indicates that the ATS is in walk mode.

Step 2: Set the Walk Speed

Once the ATS is in walk mode, you can set the walk speed. To do this, follow these steps:

1. Press the “Speed” button on the ATS control panel.
2. Use the arrow keys to increase or decrease the walk speed.
3. Press the “Speed” button again to save the changes.

The walk speed can be set from 0 to 100%. The default walk speed is 50%.

Step 3: Start Walking

To start walking, press the Start button on the ATS control panel. The ATS will start walking at the set speed.

The ATS will continue to walk until you press the Stop button.

Step 4: Stop Walking

To stop walking, press the Stop button on the ATS control panel. The ATS will stop walking and the Walk Mode indicator light will extinguish.

This guide has provided you with the steps on how to enter walk mode on an ATS. By following these steps, you can easily and safely start and stop walking with your ATS.

How do I enter Walk Mode in ATS?

1. Click the Walk Mode button in the toolbar.
2. The map will zoom out to show the entire route, and the vehicle icon will change to a walking person.
3. You can now use the mouse or keyboard to navigate the route.

What are the benefits of using Walk Mode?

• You can see the entire route at once, which can help you plan your journey.
• You can avoid traffic congestion by taking side streets or walking along sidewalks.
• You can get a closer look at landmarks and attractions along the way.

What are the limitations of Walk Mode?

• Walk Mode is not available in all areas.
• The route may not be as accurate as driving directions, especially in rural areas.
• You may have to walk on busy streets or sidewalks, which can be dangerous.

How can I get help with Walk Mode?

• You can find help with Walk Mode in the ATS Help Center.
• You can also contact ATS customer support for assistance.

  In this blog post, we have discussed how to enter walk mode in ATS. We have covered the following topics:

• What is walk mode in ATS?
• How to enter walk mode in ATS?
• The benefits of using walk mode in ATS.

We hope that this blog post has been helpful and that you now know how to use walk mode in ATS. If you have any questions, please feel free to contact us.