How To Lighten Trigger Pull On Bond Arms Derringer?

How to Lighten the Trigger Pull on a Bond Arms Derringer

The Bond Arms Derringer is a popular self-defense handgun that is known for its compact size and powerful .45 caliber round. However, one of the biggest complaints about the Derringer is its heavy trigger pull. This can make it difficult to shoot accurately, especially in a self-defense situation.

Fortunately, there are a few simple modifications that you can make to lighten the trigger pull on your Bond Arms Derringer. In this article, we will walk you through the process of lightening the trigger pull on your Derringer, so that you can shoot it more accurately and effectively.

We’ll start by discussing the different parts of the trigger mechanism and how they work together to create the trigger pull. Then, we’ll show you how to make each of these parts more efficient, which will result in a lighter trigger pull.

By the end of this article, you’ll have the knowledge and skills you need to lighten the trigger pull on your Bond Arms Derringer. This will make it a more effective self-defense handgun that you can rely on when you need it most.

Step	Instructions	Tools
1	Remove the grip panel from the Bond Arms Derringer.	– Phillips head screwdriver
2	Locate the trigger spring.	– None
3	Compress the trigger spring and bend it slightly to lighten the trigger pull.	– Needle nose pliers
4	Reinstall the grip panel.	– Phillips head screwdriver

Identifying the Cause of a Heavy Trigger Pull

A heavy trigger pull can be caused by a number of factors, including:

• Firing pin spring: The firing pin spring is responsible for driving the firing pin forward and striking the primer of the cartridge. If the firing pin spring is weak or damaged, it can cause the trigger pull to be heavier than normal.
• Trigger spring: The trigger spring is responsible for returning the trigger to its original position after it is pulled. If the trigger spring is weak or damaged, it can also cause the trigger pull to be heavier than normal.
• Sear spring: The sear spring is responsible for holding the sear in place until the trigger is pulled. If the sear spring is weak or damaged, it can cause the trigger to be released prematurely, resulting in a light trigger pull.
• Other possible causes: Other possible causes of a heavy trigger pull include a dirty or misaligned firing pin, a burr on the sear or trigger, or a problem with the firing pin block.

Inspecting and Replacing Worn or Damaged Parts

Once you have identified the cause of the heavy trigger pull, you can begin to inspect and replace the worn or damaged parts.

• Firing pin spring: To inspect the firing pin spring, you will need to remove the firing pin from the gun. Once the firing pin is removed, you can check the spring for any signs of wear or damage. If the spring is damaged, you will need to replace it.
• Trigger spring: To inspect the trigger spring, you will need to remove the trigger from the gun. Once the trigger is removed, you can check the spring for any signs of wear or damage. If the spring is damaged, you will need to replace it.
• Sear spring: To inspect the sear spring, you will need to remove the sear from the gun. Once the sear is removed, you can check the spring for any signs of wear or damage. If the spring is damaged, you will need to replace it.
• Other possible parts: If you are unable to identify the cause of the heavy trigger pull by inspecting the firing pin spring, trigger spring, and sear spring, you may need to remove other parts from the gun in order to find the problem.

By following these steps, you can identify and fix the cause of a heavy trigger pull on your Bond Arms Derringer. If you are unable to fix the problem yourself, you can take your gun to a qualified gunsmith for assistance.

3.Adjusting the Trigger Pull

The trigger pull on a Bond Arms Derringer is relatively heavy, and it may be necessary to lighten it for some shooters. This can be done by adjusting the trigger travel, trigger weight, or both.

(a) Trigger Travel

The trigger travel is the distance that the trigger must be pulled before the gun fires. It can be adjusted by loosening the two screws that hold the trigger assembly in place and then moving the trigger assembly forward or backward. Moving the trigger assembly forward will increase the trigger travel, while moving it backward will decrease the trigger travel.

(b) Trigger Weight

The trigger weight is the amount of force that must be applied to the trigger to fire the gun. It can be adjusted by loosening the screw that holds the trigger spring in place and then turning the spring clockwise to increase the trigger weight or counterclockwise to decrease the trigger weight.

(c) Other Possible Adjustments

In addition to adjusting the trigger travel and trigger weight, it may also be necessary to adjust the sear engagement. The sear engagement is the distance between the sear and the hammer when the trigger is in the fired position. It can be adjusted by loosening the screw that holds the sear in place and then moving the sear forward or backward. Moving the sear forward will increase the sear engagement, while moving it backward will decrease the sear engagement.

4.Testing the Trigger Pull

Once you have made the desired adjustments to the trigger pull, it is important to test it to make sure that it is functioning properly. To do this, load the gun with a dummy round and dry fire it several times. The trigger should break cleanly with a consistent pull weight. If the trigger does not break cleanly or if the pull weight is not consistent, you may need to make further adjustments.

(a) Before and After Adjustments

It is a good idea to test the trigger pull before and after you make any adjustments. This will help you to determine if the adjustments have made a positive difference. If the trigger pull is still too heavy or inconsistent after you have made adjustments, you may need to take the gun to a qualified gunsmith for further assistance.

(b) Final Steps

Once you are satisfied with the trigger pull, you can tighten the screws that hold the trigger assembly and sear in place. Be sure to test the trigger pull again to make sure that it is still functioning properly.

Adjusting the trigger pull on a Bond Arms Derringer is a relatively simple task that can be accomplished by most shooters. By following the steps in this guide, you can lighten the trigger pull and improve the overall performance of your gun.

How do I lighten the trigger pull on my Bond Arms Derringer?

There are a few ways to lighten the trigger pull on your Bond Arms Derringer. The most common way is to install a lighter spring. You can also polish the sear engagement surfaces, or install a trigger job kit.

To install a lighter spring:

1. Remove the grip panels from the gun.
2. Locate the trigger spring. It is a small, flat spring located just behind the trigger.
3. Remove the old spring and install the new spring.
4. Reinstall the grip panels.

To polish the sear engagement surfaces:

1. Remove the grip panels from the gun.
2. Locate the sear and the trigger.
3. Use a fine-grit sandpaper to polish the surfaces where the sear and the trigger engage.
4. Reinstall the grip panels.

To install a trigger job kit:

1. Remove the grip panels from the gun.
2. Locate the trigger and the sear.
3. Remove the old trigger and sear.
4. Install the new trigger and sear from the trigger job kit.
5. Reinstall the grip panels.

Note: If you are not comfortable working on your gun, it is best to have a qualified gunsmith perform these modifications.

What are the risks of lightening the trigger pull on my Bond Arms Derringer?

There are a few risks associated with lightening the trigger pull on your Bond Arms Derringer. First, a lighter trigger pull makes it easier to fire the gun accidentally. This could be dangerous if you are not careful. Second, a lighter trigger pull can make it more difficult to control the gun, which could lead to inaccuracy. Third, a lighter trigger pull can increase the risk of damage to the gun.

**Is it legal to lighten the trigger pull on my Bond Arms Derringer?

It is legal to lighten the trigger pull on your Bond Arms Derringer in most states. However, there are a few states that have specific laws regarding the modification of firearms. It is important to check the laws in your state before making any modifications to your gun.

What are some other ways to improve the performance of my Bond Arms Derringer?

In addition to lightening the trigger pull, there are a few other ways to improve the performance of your Bond Arms Derringer. You can install a new barrel, sights, or trigger. You can also upgrade the magazine.

To install a new barrel:

1. Remove the grip panels from the gun.
2. Locate the barrel. It is a cylindrical metal tube that is attached to the front of the gun.
3. Remove the old barrel and install the new barrel.
4. Reinstall the grip panels.

To install new sights:

1. Remove the grip panels from the gun.
2. Locate the sights. They are small metal or plastic pieces that are attached to the top of the gun.
3. Remove the old sights and install the new sights.
4. Reinstall the grip panels.

To install a new trigger:

1. Remove the grip panels from the gun.
2. Locate the trigger. It is a small metal lever that is located just behind the trigger guard.
3. Remove the old trigger and install the new trigger.
4. Reinstall the grip panels.

To upgrade the magazine:

1. Remove the grip panels from the gun.
2. Locate the magazine. It is a small metal box that is located in the grip of the gun.
3. Remove the old magazine and install the new magazine.
4. Reinstall the grip panels.

Note: If you are not comfortable working on your gun, it is best to have a qualified gunsmith perform these modifications.

there are a few different ways to lighten the trigger pull on a Bond Arms Derringer. The most common method is to install a lighter spring. This can be done by either purchasing a replacement spring from a gunsmith or by modifying the existing spring. Another option is to install a trigger kit. These kits typically include a new trigger, sear, and spring, and they can significantly reduce the trigger pull weight. Finally, it is also possible to lighten the trigger pull by polishing the contact surfaces of the trigger and sear. This will create a smoother trigger action and reduce the amount of friction.

Each of these methods has its own advantages and disadvantages. Installing a lighter spring is the simplest and most affordable option, but it may not provide as much of a reduction in trigger pull weight as a trigger kit. Trigger kits are more expensive and require more work to install, but they can produce a significant reduction in trigger pull weight. Polishing the contact surfaces of the trigger and sear is a relatively simple and inexpensive modification that can also produce a noticeable reduction in trigger pull weight.

Ultimately, the best way to lighten the trigger pull on a Bond Arms Derringer is the method that works best for you. Consider the cost, ease of installation, and desired reduction in trigger pull weight when making your decision.