How To Unclog Swiffer Wet Jet?

Swiffer Wet Jets are a convenient way to clean your floors, but they can become clogged if you’re not careful. If your Swiffer Wet Jet is clogged, don’t despair! There are a few simple steps you can take to unclog it and get it back to work.

In this article, I’ll show you how to unclog your Swiffer Wet Jet in just a few minutes. I’ll also provide some tips on how to prevent future clogs. So if you’re ready to get your Swiffer Wet Jet unclogged and back in action, read on!

Step	Instructions	Image
1	Remove the Wet Jet reservoir from the base.
2	Fill the reservoir halfway with warm water and add a few drops of dish soap.
3	Swirl the water around to loosen any clogs.
4	Rinse the reservoir thoroughly with water.
5	Reattach the reservoir to the base.

Identify the cause of the clog

Before you can fix a clog in your Swiffer Wet Jet, you need to identify what’s causing it. Here are a few common causes of clogs:

• Dirty pads: If your Swiffer Wet Jet pads are dirty, they can collect dirt and debris that can clog the nozzle. To prevent this, make sure to clean your pads regularly.
• Dried-on liquid: If you leave liquid on your Swiffer Wet Jet for too long, it can dry and harden, which can clog the nozzle. To prevent this, make sure to empty the reservoir after each use.
• Foreign objects: If you accidentally drop something into the reservoir of your Swiffer Wet Jet, it can clog the nozzle. To prevent this, be careful not to drop anything into the reservoir.

Once you’ve identified the cause of the clog, you can begin to fix it.

Try to clear the clog without disassembly

In most cases, you can clear a clog in your Swiffer Wet Jet without having to disassemble it. Here are a few things you can try:

• Rinse the nozzle: If the clog is caused by dirt or debris, you can try rinsing the nozzle with hot water. To do this, remove the nozzle from the Swiffer Wet Jet and hold it under running hot water. You can also use a toothbrush to gently scrub the nozzle.
• Use a plunger: If the clog is caused by dried-on liquid, you can try using a plunger to clear it. To do this, insert the plunger into the nozzle and push and pull several times.
• Use a pipe cleaner: If the clog is caused by a foreign object, you can try using a pipe cleaner to remove it. To do this, insert the pipe cleaner into the nozzle and gently work it around until you can dislodge the object.

If you’re unable to clear the clog using these methods, you may need to disassemble the Swiffer Wet Jet.

Disassemble the Swiffer Wet Jet

If you’re unable to clear the clog using the methods above, you may need to disassemble the Swiffer Wet Jet. Here’s how to do it:

1. Turn off the Swiffer Wet Jet and unplug it from the outlet.
2. Remove the reservoir from the Swiffer Wet Jet.
3. Remove the nozzle from the reservoir.
4. Remove the two screws on the bottom of the Swiffer Wet Jet.
5. Carefully pry open the two halves of the Swiffer Wet Jet.
6. Remove the clog from the nozzle.
7. Reassemble the Swiffer Wet Jet.

Once you’ve reassembled the Swiffer Wet Jet, you can test it to make sure the clog is cleared.

If you’re having trouble unclogging your Swiffer Wet Jet, don’t despair. By following these steps, you should be able to get your Swiffer Wet Jet up and running in no time.

Here are a few additional tips for preventing clogs in your Swiffer Wet Jet:

• Clean your pads regularly.
• Empty the reservoir after each use.
• Be careful not to drop anything into the reservoir.
• Rinse the nozzle with hot water after each use.

By following these tips, you can help keep your Swiffer Wet Jet clog-free.

Disassemble the Swiffer Wet Jet and clear the clog.

To disassemble the Swiffer Wet Jet, you will need:

• A Phillips head screwdriver
• A flathead screwdriver

1. Turn off the Swiffer Wet Jet and unplug it from the outlet.
2. Remove the water tank by pressing down on the release button and pulling it out.
3. Use the Phillips head screwdriver to remove the screws that hold the top cover in place.
4. Lift up the top cover and set it aside.
5. Use the flathead screwdriver to pry open the cap on the detergent reservoir.
6. Remove the detergent reservoir by pulling it out.
7. Use the Phillips head screwdriver to remove the screws that hold the bottom cover in place.
8. Lift up the bottom cover and set it aside.
9. Use the flathead screwdriver to pry open the cap on the water reservoir.
10. Remove the water reservoir by pulling it out.
11. Use the Phillips head screwdriver to remove the screws that hold the motor assembly in place.
12. Lift up the motor assembly and set it aside.
13. Use the flathead screwdriver to pry open the cap on the pump assembly.
14. Remove the pump assembly by pulling it out.
15. Use the Phillips head screwdriver to remove the screws that hold the impeller in place.
16. Lift up the impeller and set it aside.

Now that the Swiffer Wet Jet is disassembled, you can clear the clog.

1. Use a toothpick or a small brush to remove any debris that is blocking the nozzle.
2. If the clog is more severe, you may need to use a needle or a thin wire to clear it.
3. Once the clog is cleared, reassemble the Swiffer Wet Jet.

Reassemble the Swiffer Wet Jet and test it.

To reassemble the Swiffer Wet Jet, follow these steps:

1. Place the impeller back in the pump assembly.
2. Secure the impeller with the screws.
3. Place the pump assembly back in the Swiffer Wet Jet.
4. Secure the pump assembly with the screws.
5. Place the motor assembly back in the Swiffer Wet Jet.
6. Secure the motor assembly with the screws.
7. Place the water reservoir back in the Swiffer Wet Jet.
8. Secure the water reservoir with the screws.
9. Place the detergent reservoir back in the Swiffer Wet Jet.
10. Secure the detergent reservoir with the cap.
11. Place the top cover back on the Swiffer Wet Jet.
12. Secure the top cover with the screws.

Now that the Swiffer Wet Jet is reassembled, you can test it.

1. Fill the water tank with water.
2. Add the desired amount of detergent to the detergent reservoir.
3. Turn on the Swiffer Wet Jet and press the trigger to dispense the cleaning solution.
4. Use the Swiffer Wet Jet to clean your floors.

If the Swiffer Wet Jet is working properly, the water will flow through the nozzle and the cleaning solution will be dispensed.

If the Swiffer Wet Jet is not working properly, you may need to repeat the steps above or contact customer service for assistance.

This article has provided instructions on how to disassemble and clear a clog in a Swiffer Wet Jet. If you are unable to clear the clog yourself, you may need to contact customer service for assistance.

How do I unclog my Swiffer Wet Jet?

• Step 1: Remove the water reservoir.
• Unscrew the cap on the bottom of the Swiffer Wet Jet and remove the water reservoir.
• Step 2: Clean the filter.
• Use a small brush to clean the filter inside the water reservoir.
• Step 3: Check the nozzle.
• If the nozzle is clogged, use a needle or other thin object to gently unclog it.
• Step 4: Reassemble the Swiffer Wet Jet.
• Place the water reservoir back on the Swiffer Wet Jet and screw the cap on tightly.
• Step 5: Test the Swiffer Wet Jet.
• Turn on the Swiffer Wet Jet and spray water to make sure that it is working properly.

What else can I do if my Swiffer Wet Jet is still clogged?

• If the clog is severe, you may need to soak the Swiffer Wet Jet in a solution of warm water and vinegar for several hours.
• You can also try using a commercial declogger to clear the clog.
• If all else fails, you may need to replace the Swiffer Wet Jet.

How can I prevent my Swiffer Wet Jet from getting clogged?

• Rinse the Swiffer Wet Jet after each use.
• Empty the water reservoir regularly.
• Clean the filter regularly.
• Avoid using harsh chemicals or cleaners on the Swiffer Wet Jet.
• Store the Swiffer Wet Jet in a cool, dry place.

  there are a few simple steps you can take to unclog your Swiffer Wet Jet. First, try using a plunger to clear the clog. If that doesn’t work, you can try using a vinegar and baking soda solution. Finally, if all else fails, you can try disassembling the Wet Jet and cleaning the internal components. By following these steps, you can keep your Swiffer Wet Jet working properly and enjoy a clean home.

Here are some key takeaways:

• A plunger is a simple and effective way to clear a clog in your Swiffer Wet Jet.
• A vinegar and baking soda solution can also be used to dissolve clogs.
• If the clog is severe, you may need to disassemble the Wet Jet and clean the internal components.
• By following these steps, you can keep your Swiffer Wet Jet working properly and enjoy a clean home.