How To Attach Shock Doctor Mouthguard To Helmet?

How to Attach a Shock Doctor Mouthguard to a Helmet

Whether you’re a professional athlete or just a weekend warrior, protecting your teeth is essential. A Shock Doctor mouthguard is one of the best ways to do this, as it can help to prevent injuries in the event of a fall or collision. However, attaching a Shock Doctor mouthguard to a helmet can be tricky, especially if you’ve never done it before.

In this article, we’ll walk you through the process of attaching a Shock Doctor mouthguard to a helmet in just a few simple steps. We’ll also provide some tips on how to make sure your mouthguard stays in place and protects your teeth during play.

So whether you’re a new player or just need a refresher, read on for all the information you need to know about attaching a Shock Doctor mouthguard to a helmet.

Step Instructions Image
1 Clean the inside of your helmet with a damp cloth.
2 Apply a small amount of adhesive to the inside of the mouthguard.
3 Press the mouthguard firmly against the inside of the helmet for 30 seconds.
4 Allow the adhesive to dry completely before using your helmet.

A Shock Doctor mouthguard is a valuable piece of safety equipment for athletes of all levels. It can help protect your teeth, jaw, and lips from injury during impact. However, in order to be effective, a mouthguard must be properly attached to your helmet.

This guide will show you how to attach a Shock Doctor mouthguard to your helmet in a few simple steps.

Gather Your Materials

Before you begin, you will need to gather the following materials:

  • Shock Doctor mouthguard
  • Helmet
  • Mouthguard adhesive
  • Tape measure
  • Scissors

Prepare Your Mouthguard

First, you will need to prepare your mouthguard. If the mouthguard is not already pre-formed, you will need to mold it to your teeth.

To do this, follow these steps:

1. Remove the mouthguard from its packaging.
2. Place the mouthguard in your mouth and bite down firmly.
3. Hold the mouthguard in place with your hands and move your jaw back and forth.
4. Repeat steps 2-3 until the mouthguard is molded to the shape of your teeth.
5. Rinse the mouthguard with water to remove any debris.

Attach the Mouthguard to Your Helmet

Now that your mouthguard is prepared, you can attach it to your helmet.

To do this, follow these steps:

1. Measure the inside of your helmet with the tape measure.
2. Cut a piece of adhesive to the same length as the inside of your helmet.
3. Apply the adhesive to the inside of your helmet.
4. Place the mouthguard on the adhesive and press down firmly.
5. Allow the adhesive to dry completely.

That’s it! You have now successfully attached your Shock Doctor mouthguard to your helmet.

By following these steps, you can ensure that your mouthguard is properly secured and that you are protected from injury during impact.

Here are some additional tips for attaching a Shock Doctor mouthguard to your helmet:

  • Make sure that the adhesive is applied evenly and completely.
  • Press down on the mouthguard firmly to ensure that it is adhered to the helmet.
  • Allow the adhesive to dry completely before using the helmet.

By following these tips, you can ensure that your Shock Doctor mouthguard is securely attached to your helmet and that you are protected from injury during impact.

3. Prepare Your Helmet

To prepare your helmet for attaching the mouthguard, you will need to:

1. Find the location on the helmet where you want to attach the mouthguard. This is typically on the inside of the helmet, near the chin strap.
2. Clean the area with rubbing alcohol to remove any dirt or grease. This will help the adhesive to bond better to the helmet.

4. Attach the Mouthguard

To attach the mouthguard to your helmet, you will need to:

1. Apply a small amount of adhesive to the back of the mouthguard. Make sure to use a strong adhesive that is specifically designed for attaching mouthguards to helmets.
2. Press the mouthguard firmly against the helmet for 30 seconds. This will help to ensure that the adhesive bonds well to the helmet.
3. Allow the adhesive to dry completely before using the helmet. This will help to ensure that the mouthguard is securely attached to the helmet.

5. Wear Your Helmet

Once the mouthguard is securely attached to the helmet, you can start wearing it. Here are a few tips for wearing your helmet with a mouthguard:

  • Make sure that the mouthguard is properly fitted. It should be snug against your teeth, but not so tight that it is uncomfortable.
  • Talk to your doctor or dentist about how to properly care for your mouthguard. They can recommend the best way to clean and store it.
  • If you are involved in a collision, remove your helmet and mouthguard immediately. This will help to prevent further injury.

By following these steps, you can safely and securely attach a Shock Doctor mouthguard to your helmet. This will help to protect your teeth and mouth in the event of a collision.

How do I attach a Shock Doctor mouthguard to my helmet?

1. Make sure your mouthguard fits properly. Your mouthguard should be snug but not too tight. It should cover all of your teeth and not move around when you talk or chew.
2. Clean your helmet and mouthguard. Remove any dirt or debris from both surfaces before you attach them.
3. Apply a thin layer of adhesive to the inside of the mouthguard. Be careful not to apply too much adhesive, as this could make it difficult to remove the mouthguard later.
4. Press the mouthguard firmly against the inside of your helmet. Hold it in place for a few seconds to allow the adhesive to set.
5. Test the fit of your mouthguard. Make sure it is still comfortable and that it does not move around when you talk or chew.

What type of adhesive should I use?

You can use any type of adhesive that is designed for use on plastics. However, we recommend using a water-based adhesive, as this will be less likely to damage your helmet.

How long will it take for the adhesive to dry?

The adhesive will typically dry within a few minutes. However, it is best to wait at least 24 hours before using your helmet with the mouthguard attached.

Can I remove the mouthguard if I need to?

Yes, you can remove the mouthguard by carefully peeling it away from the inside of your helmet. However, be aware that the adhesive may leave a residue on your helmet. If this happens, you can use a mild detergent to clean it off.

What if my mouthguard comes loose?

If your mouthguard comes loose, you can reattach it by following the steps above. However, if the adhesive is no longer working, you may need to replace your mouthguard.

How can I keep my mouthguard clean?

You can keep your mouthguard clean by brushing it with a soft toothbrush and water. You can also soak it in a mouthwash solution to kill any bacteria.

Can I use a Shock Doctor mouthguard with any helmet?

Yes, you can use a Shock Doctor mouthguard with any helmet that has a hard shell. However, you should make sure that the mouthguard fits properly before you use it.

there are a few different ways to attach a Shock Doctor mouthguard to a helmet. The best method for you will depend on the type of helmet you have and your personal preferences.

If you have a helmet with a hard shell, you can use the included hook-and-loop straps to attach the mouthguard. Simply slide the straps through the slots on the mouthguard and then fasten them around the helmet.

If you have a helmet with a soft shell, you can use the included adhesive strips to attach the mouthguard. Simply peel the backing off of the strips and then press them onto the mouthguard and helmet.

Once the mouthguard is attached, you should test it to make sure it is secure. You should be able to move your jaw freely without the mouthguard coming loose.

By following these steps, you can easily attach a Shock Doctor mouthguard to your helmet and enjoy the benefits of increased protection and comfort.

Author Profile

Carla Denker
Carla Denker
Carla Denker first opened Plastica Store in June of 1996 in Silverlake, Los Angeles and closed in West Hollywood on December 1, 2017. PLASTICA was a boutique filled with unique items from around the world as well as products by local designers, all hand picked by Carla. Although some of the merchandise was literally plastic, we featured items made out of any number of different materials.

Prior to the engaging profile in west3rdstreet.com, the innovative trajectory of Carla Denker and PlasticaStore.com had already captured the attention of prominent publications, each one spotlighting the unique allure and creative vision of the boutique. The acclaim goes back to features in Daily Candy in 2013, TimeOut Los Angeles in 2012, and stretched globally with Allure Korea in 2011. Esteemed columns in LA Times in 2010 and thoughtful pieces in Sunset Magazine in 2009 highlighted the boutique’s distinctive character, while Domino Magazine in 2008 celebrated its design-forward ethos. This press recognition dates back to the earliest days of Plastica, with citations going back as far as 1997, each telling a part of the Plastica story.

After an illustrious run, Plastica transitioned from the tangible to the intangible. While our physical presence concluded in December 2017, our essence endures. Plastica Store has been reborn as a digital haven, continuing to serve a community of discerning thinkers and seekers. Our new mission transcends physical boundaries to embrace a world that is increasingly seeking knowledge and depth.

Similar Posts